Microbial Biotechnology
Electronic Journal of Biotechnology ISSN: 0717-3458 Vol. 10 No. 4, Issue of October 15, 2007
© 2007 by Pontificia Universidad Católica de Valparaíso -- Chile Received March 2, 2007 / Accepted May 24, 2007
DOI: 10.2225/vol10-issue4-fulltext-10
RESEARCH ARTICLE

Optimization of medium composition for transglutaminase production by a Brazilian soil Streptomyces sp.

Juliana Alves Macedo*
Food Science Department
Faculty of Food Engineering
Universidade Estadual de Campinas
P.O. Box 6121, CEP 13083-862
SP, Brazil
Tel: 55 19 3521 2175
Fax: 55 19 3521 2153
E-mail: jmacedo@fea.unicamp.br 

Lara Durães Sette
Brazilian Collection of Environmental and Industrial Microorganisms
Microbial Resource Division
CPQBA, Universidade Estadual de Campinas
P.O. Box 6171, CEP 13081-970
SP, Brazil
Tel: 55 19 3884 7500
E-mail: lara@cpqba.unicamp.br

Hélia Harumi Sato
Food Science Department
Faculty of Food Engineering
Universidade Estadual de Campinas
P.O. Box 6121, CEP 13083-862
SP, Brazil
Tel: 55 19 3521 2165
E-mail: heliah@fea.unicamp.br

*Corresponding author

Financial support: The authors wish to thank CNPq and Microbial Resource Division (CPQBA/UNICAMP) for their financial support.

Keywords: central composite design, fractional factorial design, medium optimization, microbial transglutaminase, Streptomyces sp. P20.

Abbreviations:

ANOVA: analysis of variances
CCD: central composite design
FFD: fractional factorial design
MTGase: microbial transglutaminase
RSM: response surface methodology
TGase: transglutaminase

Abstract

Finding a new microbial source of transglutaminase (MTGase) and the study of the medium composition for MTGase production were the goals of this work. A total of 200 actinomycete-like strains were isolated from Brazilian soil samples and two of them named T10b and P20 were selected based on their ability to produce 0.15 U.mL-1 and 0.25 U.mL-1 of MTGase, respectively. Strain P20 was chosen to continue the study and was identified as Streptomyces sp. In order to optimize the MTGase activity, modifications of the usual media composition described for enzyme production were tested. The strategy adopted was: (1) screening experiment for the best carbon and nitrogen sources; (2) fractional factorial design (FFD) to elucidate the key ingredients in the media (the results indicated that the soybean flour, peptone, KH2PO4 and MgSO4.7H2O had a significant effect on MTGase) production and (3) central composite design (CCD) to optimize the concentration of the key components. The experimental results were fitted to a second-order polynomial model at the 95% level of significance (P < 0.05). Under the proposed optimized conditions, the model predicted a MTGase activity of 1.37 U.mL-1, very closely matching the experimental activity of 1.4 U.mL-1.

Article

Transglutaminase (TGase) (EC 2.3.2.13; protein-glutamine y-glutamiyltranferase) is an enzyme that catalyses an acyl transfer reaction using peptide-bond glutamine residues as acyl donors and several primary amines as acceptors. When the ε-amino groups of the protein-bond lysyl residues are present as acyl receptors, this enzyme is capable of forming intra and intermolecular ε-(γ-Glu)-Lys isopeptide bonds (Soares et al. 2003).

The covalent cross-links between a number of proteins and peptides introduced by TGase promote the modification of the functional properties of the food proteins (Yokoyama et al. 2004). Therefore, TGase catalysed reactions may be broadly used by food-processing industries, for instance, the creation of new product textures, the modification of viscosity, the alteration of emulsifying and foaming properties, and the improvement of product nutritional value (Zhu et al. 1995; Kwan and Easa, 2003).

Transglutaminases are found in mammalian tissues, plasma, fish, and plants (Pasternack et al. 1998). The mammalian enzymes are Ca+2-dependent. However, the relatively small quantities obtained and the complex separation and purification procedures required for these enzymes led to the search for alternative microbiological sources. The first microbial transglutaminase (MTGase) characterized was from an actinomycetes (Ando et al. 1989). Since then, efforts have been made to obtain massive production of this enzyme for commercial applications, especially for the enzymes from Streptomyces (Gerber et al. 1994; Zhu et al. 1998a; Zhu et al. 1998b; Zotzel et al. 2003a; Zotzel et al. 2003b).

So far, research has been focused on the isolation and screening of microorganisms for TGase activity, and on purifying and characterizing newly found enzymes. The media compositions used to produce MTGase from Streptomyces have been almost the same in every work published since Ando et al. 1989 (Zheng et al. 2001; Zheng et al. 2002; Yan et al. 2005). In contrast, in biotechnology-based industrial processes, the formulation of the culture media is of critical importance because the composition affects product concentration, yield and volumetric productivity. It is also important to reduce the cost of the medium as this may affect the overall process economics (Souza et al. 2006).

The traditional one-at-a-time optimization strategy is simple and useful for screening, and the individual effects of medium components can be seen on a graph without the need to revert to more sophisticated statistical analyses. Unfortunately, this simple method frequently fails to locate the region of optimum response because the joint effects of factors on the response are not taken into account in such procedures. It was reported that the complexities and uncertainties associated with large-scale fermentation usually come from a lack of knowledge of the sophisticated interactions among various factors affecting fermentation (Liu et al. 2005).

Statistically based experimental designs provide an efficient approach to optimization. The fractional factorial design (FFD) is especially suitable to account for the interactions and identify the most significant components in the medium formula. A combination of factors generating a certain optimal response can be identified through factorial design and the use of response surface methodology (RSM) (Junqua et al. 1997).

RSM is a powerful technique for testing multiple process variables because fewer experimental trials are needed compared to the study of one variable at a time. Also, significant interactions between variables can be identified and quantified by this technique.

Taking into account that the soil is a great reservoir of actinomycetes and that there are few reports concerning optimization of culture medium for TGase production, in this paper we report the isolation and screening of Brazilian soil actinomycetes for TGase activity, and studied the nutritional fermentation conditions in order to maximize the TGase yield.

Materials and Methods

Selective isolation and preservation of actinomycetes

The actinomycetes strains used in this study were isolated from soil samples collected from the States of São Paulo and Bahia in Brazil.

Nearly five grams of the soil sample were added to 10 mL sterilized distilled water and the suspension was shaken at 200 rpm for 10 min. Aliquots were inoculated onto Petri dishes containing starch-casein media (Küster and Williams, 1964). The plates were incubated at 30ºC for up to 5 days. Actinomycete-like colonies were streaked onto slants of ISP2 media (0.4% yeast extract, 1% malt extract, 0.4% de glucose and agar, pH 7.0 ± 0.2) and checked for purity. Colonies were removed from the agar media and preserved in cryotubes with 10% glycerol solution at -80ºC.

MTGase-production screening

The ability to produce MTGase was determined by inoculating 1 mL of spore suspension into 250 mL Erlenmeyer flasks containing 50 mL of seed medium (Ando et al. 1989) composed of: 0.2% of peptone; 0.2% KH2PO4; 0.1% MgSO4.7H2O; 0.5% of glucose (pH 7.0). The flasks were incubated for 2 days at 30ºC and 200 rpm in a rotational shaker. Aliquots of 15 mL of pre inoculum were transferred to 135 mL of the basal medium (Ando et al. 1989) (2% of peptone; 0.2% of yeast extract; 0.2% KH2PO4; 0.1% MgSO4.7H2O; 2% of potato starch; 0.5% of glucose; pH 7.0) in 500 mL Erlenmeyer flasks and cultivated at 30ºC for 5 days at 200 rpm. All runs were made in duplicate. After that, the MTGase activity was measured as described below.

MTGase activity

Aliquots of 1 mL of culture medium were taken and after centrifugation the enzyme activity was detected in the supernatant by the colorimetric hydroxamate procedure with N-carbo-benzoxy-L-glycine according to Folk and Cole (1966) with some adaptations. Reaction mixture, containing 200 μL of enzyme, 200 μL of 0.2 M pH 6.0 citrate buffer, 25 μL of hydroxylamine, and 75 μL of 0.1 M N-carbo-benzoxy-L-glycine, was incubated at 37ºC for 1 hr and then the reaction was stopped by adding an equal volume (500 μL) of 15% three chloride acetic acid (TCA) containing 5% FeCl3. The absorbance was measured at 525 nm (Beckman coulter DU 640). One unit of MTGase activity was defined as the amount of enzyme which causes the formation of one micromole of hydroxamic acid per min at 37ºC. A calibration curve was prepared using L-glutamic acid y-monohydroxamate.

Preliminary tests

Testing high viscosity medium fermentation. This test consisted of adding the contents of one cryotube (two agar-mycelium cylinders nearly 0.6 cm in diameter) directly into 15 mL of the modified basal medium composed of: peptone (2%); KH2PO4 (0.2%); MgSO4.7H2O (0.1%); potato starch (2%); glucose (0.2%); and soybean flour (2%) (pH 7.0). This was done in 50 mL Erlenmeyer flasks and cultivated for 5 days at 100 rpm in a rotary shaker. An aliquot of 1 mL was taken at 120 hrs, and the enzyme activity measured as described above in section MTGase activity.

Screening for the optimal sources of carbon and nitrogen. The effects of different sources of nitrogen and carbon on the MTGase production were investigated with the one-by-one time strategy. The nitrogen sources and corresponding concentrations tested were: peptone 2% with yeast extract 0.2%; peptone 2%; corn steep liquor (CSL) 2%; and casein 2%. The carbon sources were: potato starch 2% with glucose 0.2%; molasses 2%; sucrose 2%; maltodextrin 2%; glycerol 2%; and soluble starch 2%. In the investigation of the nitrogen sources, growth was carried out in the medium containing: 0.2% KH2PO4; 0.1% MgSO4.7H2O; 2% soybean flour; 2% potato starch; 0.2% glucose. In the process of screening carbon sources, fermentation was carried out using the medium containing: 0.2% KH2PO4; 0.1% MgSO4.7H2O; 2% soybean flour; and 2% peptone.

The optimization procedure and experimental design

All experimental design results were analyzed using STATISTICA 5.0 for Windows (Statsoft, Inc.).

Elucidation of the significant components using a FFD. A 2(6-2) FFD was employed to determine the key ingredients that affected TGase production significantly. There were six nutrient factors in the medium, which were: peptone, KH2PO4, MgSO4.7H2O, potato starch, soybean flour and glucose. Each factor was examined at a high level (coded +1) and a low level (coded -1), which corresponded to the basal level ± 50%, respectively. The center points were the trials under the basal level conditions (coded 0). Table 1 shows the variables and levels in detail. A ¼ fraction of the full factorial design was adopted; consequently, the experiment included 16 (26-2) combinations plus two replicates at the center point, as shown in Table 1. Each trial was performed only once, and the enzyme activity was measured at 72 hrs, 96 hrs and 120 hrs of fermentation.

Optimization of key ingredients concentrations using a central composite design (CCD). The medium components that affected TGase production significantly were optimized using a CCD design. The variables were coded according to the equation [1]:

       [1]

where xi is the coded variable of a nutrient factor, Xi is the natural variable of the nutrient factor. Xo is the value of the natural variable at the center point, and ∆Xi is the step change value. The variables and levels are shown in Table 2.

The statistical software defined a full CCD design for 4 factors consisting of 24 combinations plus the replicates at the center point (16 cubic points, 8 star points and 2 replicates at the center point to estimate the experimental error and to investigate the suitability of the proposed model); details are illustrated in Table 2. Once the experiments had been performed, the experimental results were fitted to a second-order polynomial function. The Student t-test permitted us to check the statistical significance of the regression coefficients, and the analysis of variances (ANOVA) was performed on the experimental data to evaluate the statistical significance of the model. The model for the response was expressed in terms of coded variables, without taking into account the statistically non-significant terms.

Results

The strategy employed in this study, comprising selective isolation conditions for actinomycetes using different Brazilian soil samples, was successful for the recovery of about 200 actinomycete pure cultures. These isolates were investigated for TGase production and the results showed that stronger enzyme activity was found in the actinomycete strains T10b (0.15 U.mL-1) and P20 (0.25U.mL-1). The latter strain was chosen to continue the studies andwas taxonomically identified by molecular methods as Streptomyces sp. and subsequently deposited in the Brazilian Collection of Environmental and Industrial Microorganisms (CBMAI) under the number CBMAI 837, to be available for further investigations.

In order to optimize the MTGase activity, modifications of the usual media components reported for enzyme production were tested. Data from the high viscosity medium fermentation test showed that Streptomyces sp. (strain P20) presented higher activity on this medium (1.1 U.mL-1) when compared with the MTGase activity obtained on the basal medium (0.20 U.mL-1) after 120 hrs of fermentation.

The results of the effects of the carbon and nitrogen sources on the MTGase activity produced by Streptomyces sp. P20 are shown in Figure 1. Of all nitrogen sources investigated, the most promising was peptone, where the MTGase activity was about 1.12 U.mL-1. For the carbon source, the best results were obtained with a mixture of potato starch and glucose (1.12 U.mL-1) and with maltodextrin (1.18 U.mL-1). Since the results for both carbon sources were not significantly different, the cheapest source (potato starch and glucose) was chosen to continue the study.

The next step was to define each of the media components affecting MTGase production significantly and to determine the best concentrations of each. As a preliminary step for optimization, the most important nutrient factors were screened by applying the two-level FFD as described in materials and methods. The experimental design and the results of the FFD observations are presented in Table 1. TGase production varied greatly from 0.02 to 1.27 U.mL-1 with different combinations of the components in the media. The main effects are shown in Table 3.

In order to optimize the key ingredients selected in the media, a CCD was made. The experimental design and results are shown in Table 2. The quadratic model calculated for maximum MTGase activity, after eliminating the statistically insignificant terms (p > 0.05), was:

Y = 1.3675 - 0.20602x12 - 0.1652x22 - 0.11622x3 - 0.14376x32 - 0.09508x4 - 0.16281x42 + 0.106293x1.x2 - 0.07399x1.x4 - 0.1557x3.x4

The ANOVA reproduced in Table 4 showed that the model was significant. The Fisher F-test (F9;17 = 14.2 > Ft 0.95;9;17 = 2.49) was 5-6 times higher than the Ft, and the p-value <0.000001 did in fact demonstrate that this regression was statistically significant at the 95% confidence level. Besides, the R2 (multiple correlation coefficient) of the regression equation obtained I was 0.88 (a value >0.75 indicates aptness of the model), which means that the model can explain 88% of the variation in the response.

Three response surfaces were chosen among the possible combinations as representative of each selected rotation speed to visualize the simultaneous effects of peptone, soybean flour, KH2PO4 and MgSO4.7H2O on MTGase production pattern (Figure 2).

Discussion

A Streptomyces sp. strain was isolated from a Brazilian soil sample as a potential producer of TGase; it was found to be an extracellular producer, with a calcium independent enzyme, which makes it much more interesting and practical for industrial use (Yokoyama et al. 2004).

The fermentation of P20 in the higher viscosity medium was adequate, since a consistent formation of pellets was observed during growth on the liquid medium. According to previous experience in our laboratory, this behavior was already observed for a fungus that was used to growing on a solid medium, when exposed to a liquid medium, and indicated that the microorganism was not well adapted to the medium. Another reason that moved us to try a higher viscosity medium for the enzyme production was the inconsistency of the results obtained in the liquid medium. The lack of repeatability of the values of MTGase activity made it necessary to run several tests. The tests indicated that the microorganism could grow well in a rich liquid, but with no MTGase production at all. On the other hand, MTGase activity reached much higher levels (5.5 times higher) in experiments where the microorganism had some kind of physical support to grow on. These results further supported the hypothesis raised by Yan et al. (2005) that MTGase is probably involved in the formation of covalent bonds between different cell wall proteins (to provide the mycelium growing in Streptomyces).

In order to select the best and less expensive sources of nitrogen and carbon for the production of TGase, different compounds were investigated with the one-by-one time strategy. Data from these experiments showed that better results were obtained when peptone was used as the nitrogen source (1.12 U.mL-1) and when a mixture of potato starch and glucose (1.12 U.mL-1); and maltodextrin (1.18 U.mL-1) were used as carbon sources. The results for both carbon sources were not significantly different and for that reason the source with the lower price (potato starch and glucose) was chosen to continue the study. For the next step, the FFD study, the salts of the media were the only independent variables that had not previously been tested; they were used according to the literature data.

Observing the results of the FFD experiment, it was clear that variations in the concentration of potato starch, peptone and glucose did not affect MTGase production significantly at the levels tested. Considering this, the glucose concentration was fixed at the minimum value for the next factorial design, and the concentration of potato starch was fixed at the intermediary level. Since peptone is the most expensive compound in the fermentation medium, its concentration was not fixed at the level -1 for the next study, because we hoped to find an even lower concentration where it would still not interfere with the MTGase activity significantly. On the other hand, the enzyme production was greatly affected by soybean flour, KH2PO4 and MgSO4.7H2O (p < 0.05). These three nutrient components and peptone were further investigated in a broader range of concentration within a CCD.

The results from the CCD showed that the optimal concentrations of the four key ingredients were basically the same values of the central point: 2.5% soybean flour; 0.4% KH2PO4; 0.2% MgSO4.7H2O and 1.0% peptone. However, it was not possible to reduce the peptone concentration without reducing the MTGase activity. The maximum MTGase activity predicted by the model was calculated to be 1.37 U.mL-1. In order to confirm the predicted results and validate the regression obtained, experiments using the improved formula for the media were performed, and a value of 1.4 U.mL-1 (n = 3) was obtained. It was shown that the model was adequate to predict the optimization of MTGase production of Streptomyces sp. P20.

The fermentation media for MTGase production has been almost the same in every published work since Ando et al. (1989). In this work we have modified and optimized the fermentation media for MTGase production using statistical methods. From the present study, it is evident that the use of a FFD statistical design and CCD can be used to determine the significant variables and the optimum conditions for MTGase production, respectively. The optimization of the medium resulted not only in an 86% higher MTGase activity than in the media previously cited in the literature, but also in a reduction of the constituents costs and an improvement in repeatability. It is important to observe that the value of 1.4 U.mL-1 of MTGase activity obtained in this study is significant when compared with values previously reported in the literature that ranged from 0.25 U.mL-1 to 2.5 U.mL-1 (Zhu et al. 1995). In addition, the relevance of these results is that the factors leading to the increased activity were identified and are important for further studies.

Considering the results obtained in the present study, the conclusion was that the Brazilian soil isolate Streptomyces sp. P20 offers great potential for further investigation on MTGase production. Therefore, experiments involving other aspects of production (optimization of temperature and agitation conditions) and characterization of the enzyme are being carried out. In addition, strain P20 will be taxonomically characterized by using the polyphasic approach, in order to have a more accurate identification.

References

ANDO, Hiroyasu; ADACHI, Masae; UMEDA, Koichi; MATSUURA, Akira; NONAKA, Masahiko; UCHIO, Ryosuke; TANAKA, Haruo and MOTOKI, Masao. Purification and characteristics of a novel transglutaminase derived from microorganisms. Agricultural and Biological Chemistry, March 1989, vol. 53, no. 10, p. 2613-2617.

FOLK, J.E. and COLE, P.W. Mechanism of action of pig liver transglutaminase. Mechanism of action of guinea pig liver transglutaminase. I. Purification and properties of the enzyme: identification of a functional cysteine essential for activity. The Journal of Biological Chemistry, December 1966, vol. 241, no. 23, p. 5518-5525.

GERBER, Ulrike; JUCKNISCHKE, Ute; PUTZIEN, Sybille and FUCHSBAUER, Hans-Lothar. A rapid and simple method for the purification of transglutaminase from Streptoverticillium mobaraense. Biochemical Journal, May 1994, vol. 299, no. 3, p. 825-829.

JUNQUA, M.; DURAN, R.; GANCET, C. and GOULAS, P. Optimization of microbial transglutaminase production using experimental designs. Applied Microbiology and Biotechnology, December 1997, vol. 48, no. 6, p. 730-734. [CrossRef]

KÜSTER, E. and WILLIAMS, S.T. Selection of media for isolation of streptomycetes. Nature, May 1964, vol. 202, no. 4935, p. 928-929. [CrossRef]

KWAN, Soo-Wei and EASA, Azhar-Mat. Comparing physical properties of retort-resistant glucono-δ-lactone tofu treated with commercial transglutaminase enzyme or low levels of glucose. Lebensmittel-Wissenschaft und-Technologie, February 2003, vol. 36, no. 6, p. 643-646.

LIU, Junguo; XING, Jianmin; GHANG, Tianshi; MA, Zhiya and LIU, Huizhou. Optimization of nutritional conditions for nattokinase production by Bacillus natto NLSSE using statistical experimental methods. Process Biochemistry, July 2005, vol. 40, no. 8, p. 2757-2762. [CrossRef]

PASTERNACK, Ralf; DORSCH, Simone; OTTERBACH, Jeans; ROBENEK; Isabella; WOLF, Sabine and FUCHSBAUER, Hans-Lothar. Bacterial pro-transglutaminase from Streptoverticillium mobaraense, purification, characterization and sequence of the zymogen. European Journal of Biochemistry, November 1998, vol. 257, no. 3, p. 570-576. [CrossRef]

SOARES, Luis Henrique de Barros; ASSMANN, Francine and AYUB, Marcos Antonio Záchia. Purification and properties of a transglutaminase produced by a Bacillus circulans strain isolated from the Amazon environment. Biotechnology and Applied Biochemistry, June 2003, vol. 37, no. 3, p. 295-299. [CrossRef]

SOUZA, Claucia Fernanda Volken; FLORES, Simone Hickmann and AYUB, Marcos Antônio Záchia. Optimization of medium composition for the production of transglutaminase by Bacillus circulans BL32 using statistical experimental methods. Process Biochemistry, May 2006, vol. 41, no. 5, p. 1186-1192. [CrossRef]

YAN, Guoliang; DU, Guocheng; LI, Yin; CHEN, Jian and ZHONG, Jianjiang. Enhancement of microbial transglutaminase production by Streptoverticillium mobaraense: application of a two-stage agitation speed control strategy. Process Biochemistry, February 2005, vol. 40, no. 2, p. 963-968. [CrossRef]

YOKOYAMA, K.; NIO, N. and KIKUCHI, Y. Properties and application of microbial transglutaminase. Applied Microbiology and Biotechnology, May 2004, vol. 64, no. 4, p. 447-454. [CrossRef]

ZHENG, Meiying; DU, Guocheng; GUO, Wangfang and CHEN, Jian. A temperature-shift strategy in batch microbial transglutaminase fermentation. Process Biochemistry, January 2001, vol. 36, no. 6, p. 525-530. [CrossRef]

ZHENG, Meiying; DU, Guocheng and CHEN, Jian. pH control strategy of batch microbial transglutaminase production with Streptoverticillium mobaraense. Enzyme and Microbial Technology, September 2002, vol. 31, no. 4, p. 477-481. [CrossRef]

ZHU, Y.; RINZEMA, A.; TRAMPER, J. and BOL, J. Microbial transglutaminase- a review of its production and application in food processing. Applied Microbiology and Biotechnology, December 1995, vol. 44, no. 3-4, p. 277-282. [CrossRef]

ZHU, Y.; RINZEMA, A.; TRAMPER, J.; BRUIN, E. and BOL, J. Fed-batch fermentation dealing with nitrogen limitation in microbial transglutaminase production by Streptoverticillium mobaraense. Applied Microbiology and Biotechnology, March 1998a, vol. 49, no. 3, p. 251-257. [CrossRef]

ZHU, Y.; RINZEMA, A.; BONARIUS, H.P.J.; TRAMPER, J. and BOL, J. Microbial transglutaminase production by Streptoverticillium mobaraense: Analysis of amino acid metabolism using mass balances. Enzyme and Microbial Technology, August 1998b, vol. 23, no. 3-4, p. 216-226. [CrossRef]

ZOTZEL, J.; KELLER, P. and FUCHSBAUER, H.-L. Transglutaminase from Streptomyces mobaraensis is activated by an endogenous metalloprotease. European Journal of Biochemistry, August 2003a, vol. 270, no. 15, p. 3214-3222. [CrossRef]

ZOTZEL, Jeans; PASTERNACK, Ralf; PELZER, Christiane; ZIEGERT, Dagmar; MAINUSCH, Martina and FUCHSBAUER, Hans-Lothar. Activated transglutaminase from Streptomyces mobaraensis is processed by a tripeptidyl aminopeptidase in the final step. European Journal of Biochemistry, October 2003b, vol. 270, no. 20, p. 4149-4155. [CrossRef]

Note: Electronic Journal of Biotechnology is not responsible if on-line references cited on manuscripts are not available any more after the date of publication.

Supported by UNESCO / MIRCEN network